C2TE S1 Kalekim Technoflex Wall & Floor Deformable Tile Adhesive Grey and White Colour Option (20 Kg) Suitable for Porcelain Ceramic & Granite Tiles

C2TE S1 Kalekim Technoflex Wall & Floor Deformable Tile Adhesive Grey and White Colour Option (20 Kg) Suitable for Porcelain Ceramic & Granite Tiles

  • £13.69
Tax included. Shipping calculated at checkout.


Product Definition
High performance cementitious flexible adhesive with extended open time and reduced slip for ceramic tiles and stones.

Application Areas
  • Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, porcelain tiles natural stone, marble, granite, clinker, cotto on cementitious renders, cementitious screeds and concrete.
  • Bonding of tiles on existing ceramic tile, granite.
  • Bonding of tiles on painted walls and gypsum.
  • Bonding of ceramic tiles in swimming pools, basins and any other wet places.
  • Bonding of tiles on terraces and balconies.
  • Bonding of tiles on places where sudden temperature changes occurs like cold storage depots and over floor heat installations.
  • Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools.

Features
  • Perfect adherence.
  • Highly Deformable, resistant to temperature chan- ges.
  • Can be applied on vertical surfaces even for bonding of heavy tiles without sagging.
  • Extended open time.
  • Easily trowellable.

Technical Features
(at 23°C and 50% RH)

General Data:
  • Appearance: Grey or White powder
  • Shelf Life: 12 months when stored in the original sealed packing in dry place.

Application Data:
  • Application Temperature Range: (+5°C) - (+35°C)
  • Mixing Ratio: 6 - 7.5 litres water / 25 kg powder
  • Pot Life: Approx. 6 hours
  • Slip (EN 1308): ≤ 0.5 mm
  • Open Time (EN 1346): After 30 minutes ≥ 0.5 N/mm²
  • Grouting: 8 hours on wall; 24 hours after on floor
  • Consumption: 3-5 kg/m²

Performance Data:
  • Tensile Adhesion Strength (EN 1348)
  • -initial (after 28 days): ≥ 1 N/mm²
  • -after heat exposure: ≥ 1 N/mm²
  • -after immersion in water: ≥ 1 N/mm²
  • -after freeze/thaw cycles: ≥ 1 N/mm²
  • Deformability (EN 12002): ≥ 2.5 mm-S1 Deformable
  • Service Temperature Range (after final cure): (-40°C)-(+80°C)
  • Dangerous Substances (EN 12004): Complies
  • Reaction to Fire: A1

Application Instructions
  • Substrates must be sound, free from oil, grease, and sufficiently dry. Cementitious substrates must be cured.
  • Wipe the back side of tiles with water if dusty.
  • Pour 20 kg of TECHNOFLEX into 5-6 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application
  • Allow to stand for 5-10 minutes to mature. After 1-2 minutes remixing, the paste is ready for application.
  • Spread the mortar onto the substrate with notched trowel of which notch size is appropriate to the tile dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of TECHNOFLEX with the flat side of trowel, then notch with the toothed side of trowel.
  • Applications of large tiles (greater than 40x40 cm), on existing tiles or which are subject to frost or heavy traffic, TECHNOFLEX should be applied also on the back of tiles. (combined method)
  • Open time is 30 minutes. Install the tiles within this period with pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar.
  • Dispose mortars of which pot life is expired. Clean tools and hands with water, surfaces with a damp cloth.
  • Tiles installed with TECHNOFLEX must not be subject to water for at least 24 hours.

Warnings

  • Since contains cement, irritating to eyes, respiratory system and skin. For further information refer to safety data sheet.
  • Indicated consumption is a general information. It may change depending on the application conditions and surface properties.

Storage
  • Store in dry medium. Do not stack more than 10 bags on top of each other.

Packaging
  • 20 kg multi-ply paper bags.

Quality Documents
  • TS EN 12004, Class C2TE, S1
  • C: Cementitious
  • 2: Improved
  • T: Reduced slip
  • E: Extended Open Time
  • S1: Deformable