CG2 WA Kalekim Fugapool Flexible Grouting Mortar Additive Flex Tile Grout 1-6 mm (5 Kg)

CG2 WA Kalekim Fugapool Flexible Grouting Mortar Additive Flex Tile Grout 1-6 mm (5 Kg)

  • £11.39
Tax included. Shipping calculated at checkout.

Product Definition
  • High performance (high resistance to abrasion and reduced water absorption), cementitious flexible fungee and yeast resistant grout for 1 to 6 mm joints.

Application Areas
  • Floor and wall grouting of wet places like swimming pools, water tanks, bathrooms, balconies, Turkish Bath, sauna, thermal spring.
  • Grouting places where sudden temperature changes and heavy traffic exist like facades, terraces, over floor heating installations, warehouses.
  • Grouting interior and exterior floor and wall in all types and sizes of ceramic tiles, granite, cotto, clinker, glass mosaics, marble, natural stone for 1-6 mm joints.

  • Resistant to fungee and yeast.
  • Approved to be used in contact with water intended for human consumption.
  • Good compressive and flexural strength and good resistance to freeze/thaw cycles.
  • Low water absorption.
  • Low shrinkage, therefore absence of cracks and fissures.
  • A smooth final surface.
  • Very good abrasion resistance.
  • Fast curing
  • Ultra-violet and atmosphere resistant 2 different colours.

Technical Features
  • (at 23°C and 50% RH)

General Data
  • Appearance: White and coloured powder
  • Shelf Life: 12 months when stored in the original sealed packing in dry place.

Application Data
  • Mixing Ratio: 6-6.6 litres water / 20 kg powder
  • Application Temperature Range: (+5°C)-(+35°C)
  • Pot Life: 1 hour
  • Set to Light Traffic: 12 hours
  • Consumption: See consumption table depending on width of the joints and dimensions of the tile.

Performance Data
  • Flexural Strength (EN 12808-3): ≥ 2.5 N/mm²
  • Compressive Strength (EN 12808-3): ≥ 15 N/mm²
  • Flexural Strength (after freze/thaw cycles) (EN 12808-3):
  • ≥ 2.5 N/mm²
  • Compressive Strength (after freze/thaw cycles) (EN 12808-3):
  • ≥ 15 N/mm²
  • Abrasion Resistance (EN 12808-2): ≤ 1000 mm³
  • Shrinkage (EN-12808-4): ≤ 3 mm/m
  • Water Absorption (after 30 min / 4 hours) (EN 12808-5):
  • ≤ 2 gr / ≤ 5 gr
  • Service Temperature Range (after final cure): (-30°C)-(+80°C)

Application Instructions
  • Before grouting, wait until the adhesive has completely set.
  • The joints must be clean, free of dust and raked back to at least 2/3 of the tile thickness.
  • Wet the joints with clean water when using very porous ceramic tiles in high temperatures and in the presence of wind.
  • Pour 5 kg of FUGAPOOL into 2-2.5 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Amount of water should be precisely measured. Do not add any additive which is not mentioned in the instructions for the application Excess water can cause cracking, low abrasion resistance and colour defects.
  • Allow to stand for 5-10 minutes to mature. After 1-2 minutes remixing, the paste is ready for application.
  • Fill the joints completely with FUGAPOOL using the appropriate rubber trowel, making sure the joints are completely compacted. Remove excess FUGAPOOL from the surface moving the float diagonally across joints.
  • When the mixture loses its plasticity and becomes matt, usually after 10-20 minutes, clean the surface with a damp sponge working diagonally to the joints. If cleaning is carried out when the mixture is stil plastic, the grout may be dragged from the joint leading to colour variations.
  • Any residue left can be cleaned from the surface with a clean dry cloth.
  • Dispose mortars of which pot life is expired. Clean tools and containers with plenty of water before FUGAPOOL hardens.
  • When applying FUGAPOOL in extremely hot, dry or windy climates, it is recommended to wet the joints after several hours to improve the final performance.


  • Since contains cement, irritating to eyes, respiratory system and skin. For further information refer to safety data sheet.

  • Store in dry medium. Do not stack more than 10 bags on top of each other.
  • 5 kg polyethylene bags

Quality Documents
  • TS EN 13888, Class CG2WA
  • C: Cementitious
  • G: Grout
  • 2: Improved
  • W:Reduced Water Absorption
  • A:High Abrasion Resistance

Hacettepe University Doping Control Center Approval Report according to BS 6920 (suitable for use in contact with water intended for human consumption)